Showing results: 376 - 390 of 651 items found.
-
SR1020F -
Hangzhou Softel Optic Co., Ltd.
Designed for FTTH(Fiber To The Home) networks ●Excellent linearity and flatness ●Wide range of optical input power ●Single-mode fiber high return loss ●Using GaAs amplifier active devices ●Ultra low noise technology ●Smaller size and easier install ●Red-LED for power indication ●Color-LED for optical power indication ●Build-in filter●Double color LED for optical power indication (Non-lighted:optical power<-10dBm, Green: -10dBm+3dBm)
-
Analog Devices Inc.
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption,high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
11867A -
Keysight Technologies
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
Analog Devices Inc.
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
Analog Devices Inc.
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Model 30/20A -
TREK, INC.
The Model 30/20A is a DC-stable, high-voltage power amplifier designed to provide precise control of output voltages in the range of 0 to ±30 kV DC or peak AC with an output current range of 0 to ±20 mA DC or peak AC. The amplifier is configured as noninverting with a fixed gain of 3000 V/V. Inverting and differential input options are available. A calibrated potentiometer provides a DC offset over a range of 0 to ±30 kV DC.
-
Teledyne RF & Microwave
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
BE-A -
Panasonic Industrial Devices Sales Company of America
*One-touch Attachment*For Small Diameter Tubes*High Speed Response Time*Ultra Compact*For A Wide Range Of Power Supply Voltages*Built-In Amplifier*Allows For Close Proximity Attachment*CE Approved*CE: EMC Directive
-
HAPM1000 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
HAPM4000 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Acroname, Inc
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
ZET 412 -
ZETLAB Company
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
S95086B -
Keysight Technologies
The S95086B Gain-Compression Measurement (GCA) software provides fast and accurate input power, output power, gain, and phase at the compression point of an amplifier or frequency converter over a specified frequency and power range. With a simple setup, GCA reduces test times through an easy-to-use, fast, and accurate SMART Sweep. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
-
UC8202 -
UC Instruments, Corp.
The UC8202 Dual channel optical power meter offer superior performance for the test of DWDM components, AWG , WSS, OPM, PLC components, optical amplifiers, transceiver/receiver and other general purpose of fiber optical test and measurement applications